Steelcase and AMQ are high-end office furniture brands normally absent in the “affordable, entry-level” category where this sit-stand desk squarely sits. So, I was skeptical. After use though, my opinion is this isn’t a “paste famous name on junk and call it a day” product. For the money I think it’s as well-designed and stable as you’ll find. Its lackluster controller is a drawback, and its last inches of height are unusable. But it’s consideration worthy for anyone not NBA center height. For these reasons I give it 4-stars.
I put it though a few tests. I’ll review those and my use experience and assembly process. Bottomline though, if you are looking for an attractive, quality built (by entry level standards) sit-stand desk and are of 1) average or lower height, 2) won’t put much weight on it or 3) use it like a traditional office desk, consider it.
BUILD QUALITY, AESTHETICS, AND FUNCTIONALITY
Build material quality is good plus it’s UL Listed, an important distinction to me among its competition. Also on the safety front, there’s anti-collision protection similar to a garage door opener – when it detects its going to hit something it immediately stops. This is especially important if you have kids.
It weighs around 100 lb. so it doesn’t easily shift around the floor. Half its weight is the 1” thick single-piece laminate desktop. A single piece is more stable and attractive than a cheaper two-piece design.
The top color I have is called “light oak,” but looks light maple color to me. The corners are rounded, and all edges are slightly beveled to eliminate sharp areas. There are no visual seams or exposed screws and overall, the desk appears more upscale than its price. There is no under-desk storage but if you want to install some there is about 8” of usable depth ahead of the power supply and wiring.
The legs and feet are beefy with the heft of a small anchor. I didn’t weight them but guessing 20-25 lbs. each. The feet have adjustable stands to prevent rocking if your floor isn’t level.
While some assembly is required, 99% of the electronics, including the power supply and a single motor, are pre-installed under the tabletop. The motor moves the desktop smoothly top-to-bottom. When churning, ambient room noise increased from approximately 38 dB to 50 dB, according to the app I used, so borderline noisy. The sound is between a “purr” and a “whine.”
The controller is no-frills with only a small LED display showing the current height of the desk and silicone-covered up and down buttons to adjust height. A button must be continually pressed until the desired height is reached. I’m not a fan of the controller’s lack of features, but its buttons are tactile, responsive, and feel pleasant. Even as an entry level desk, such a basic controller is a disappointment. I’ve seen less expensive desks with way more sophisticated control options – though I can’t speak to those desk’s overall quality. This controller is the one aspect that I find truly objectionable about this desk. There is no onboard Wi-Fi or Bluetooth and therefore no app or voice assistant compatibility.
All sit-stand desks are inherently less stable than traditional desk since they have extending and retracting legs. In the entry level tier, particularly, expecting and accepting some wobble is a must. They all have some wobble, but some have less than others. So, I conducted a few tests to pinpoint what conditions render this desk impractical.
To be clear, when I discuss wobble it’s the result of me pushing or pressing on the table trying to get it to shimmy.
MOTOR STRENGTH
First up, motor speed and smoothness. How fast does it go from fully retracted 28” to full height of 47.5” and vice versa, and is it smooth or jerky. Repeat 3x for an average. Then I added 10 lbs., then 20 more, and finally 50lb on the desktop. I stopped at 50 lb. even though the desk’s maximum weight is 144 lbs. because I don’t see people loading up more than 50 lbs. here. A small desktop, a couple monitors and a desk printer, combined, weighs maybe 20-25 lbs.
The trip from 47.5” to 28” and vice versa, averaged 18 seconds effortlessly, regardless of weight on it. That’s quite respectable and a testament to the motor’s vigor. A lesser motor will slow, maybe stutter, as weight is added. Few people (probably no one) will be using this desk at 47.5”, so for a more usable data point, going from 28” to 40” takes about 11 seconds or just under a second per inch by my stopwatch.
WOBBLE TEST
Disclaimer - this section contains raw data to offer prospective buyers a sense of what they are getting. Please don’t conflate with the desk’s usability because it’s only half the story. I’ll discuss real life usability and my experience in the next section.
OK, the wobble test. Here I gently move the palm of my hand on the table or poke the side. The goal is to simulate “real use” circumstances – dropping a book, bumping my body against it, etc. I repeated this at various heights and for the desk’s long and short ends, though I think most people stand at the long end. I added weight after each round until I reached 50 lbs. With the understanding this is an entry level product, the results pleased me but did not surprise. It’s irrational to expect Corvette quality in a Malibu. Compared to what I’ve seen in true low-end desks, this Steelcase AMQ desk is reasonably stable… reasonably.
Unlike to the speed test, weight load did factor here. Generally, as weight load increased, stability decreased both front to back and side-to-side, most notably after 37”. At 28”, the desk’s lowest level, wobble is effectively non-existent regardless of weight on the desktop, on par with a moderately price fixed-height table. Up to 37” wobble exists, but is minimal, again regardless of weight on it. After this point height and weight figure in so it was no shock it was easier to get the table to wobble with 50 lbs. on the desktop at 45-47” high. I wish I could quantify the wobble more scientifically, but the point here is it the level of wobbling above 44” increases significantly and adding weight will magnify it more. Still, the amount of wobble in the 38”- 44” range is less than most of the desk’s peers I’ve seen, and as I’ll discuss below, not enough to interfere with working comfortably.
“REAL USE” TEST CASES
I separately used two different laptops, one a 14” with firm display hinges and then a 16” with looser hinges. For some ambiance I also added a small 3 lb. potted plant garden. I will use the desk as a place to use my laptops, so it’s my real-life setup. In this test I work normally and do not intentionally force wobble as I did in the wobble test.
In each test I started working at 39” and raised the table a few inches every 10 minutes until I reached 47”. I’m not a tall person, so eventually I needed the help of a step stool to get me to the equivalent of about 5’11”.
Using the firm-hinged laptop, typing at a 50-wpm pace, I never notice shaking. At every height the table felt more stable than my wobble tests suggested, probably because the force was indirectly pushing down on the desk rather than directly into or on the desk. Where wobble enters the picture here is when I physically touch the table, be it a palm push off or a body bump. As noted, in my wobble test, as the height increases so does the desks sensitivity. Naturally, with the approximate same level of force applied, it’s a weaker wobble at 39” than at 44”
Wobble was more perceptible using the looser-hinged laptop, especially at the 45” level where I noticed my display movements, small as they were. Especially at the higher desk heights around 45” it become unusable to me. 45-47” though is the last 3” of this desk. Most people will not need to go this high, but definitely measure what is comfortable to you before ordering.
While I did not test with a desktop and display monitor I think it’s reasonable to extrapolate one would have a similar experience with a display that did not have a solid foot/feet. In that vein, I would not attach a VESA monitor arm to the desktop.
POST-TEST DEDUCTION - WHO IS THIS DESK BEST FOR?
While not “scientific,” I think my tests are useful enough to evaluate how and how not to use this desk. Every sit-stand desk at this tier has wobble, and I think this Steelcase AMQ is the among best available at this price range. It clearly has weak points, so the question not turns to: who is the ideal user for this desk?
The answer, I believe, average height or shorter people who won’t need raise the table more than 44” to be in a comfortable typing position. Additionally, it’s best as a supplement to a traditional desk or to be used as convenient place to use a laptop instead of the couch.
Equipment matters too, more so at its higher elevation range. I think a happy user will have a modest setup - laptop or small desktop, 27” monitor and a pair of compact speakers. I would not treat it like a traditional desk.
ASSEMBLY
I left this for last because I think it’s the most insignificant part of the buying decision here. The desk ships in one gigantic 100 lb.-ish box. It’s assembled upside down, which can be done by one person. When it’s time to turn the desk over, unless you have the height, arm span, and brawn of Paul Bunyan you will need two people.
The most difficult part of the assembly is closing the lever that supports the legs. This requires using a little muscle – I bopped it with a mallet instead. But if you have any kind of shoulder or upper arm injury or are in recovery take note. The feet are screwed in, and the cable management cover, if you choose to use it, is a combination of screws and clicking into place.